Update desired_maximum_frame_latency documentation

examples/features/src/framework.rs

@@ -196,6 +196,8 @@ impl SurfaceWrapper {
             config.format = format;
             config.view_formats.push(format);
         };
+        config.present_mode = wgpu::PresentMode::Immediate;
+        config.desired_maximum_frame_latency = 3;
 
         surface.configure(&context.device, &config);
         self.config = Some(config);

wgpu-types/src/lib.rs

@@ -5789,25 +5789,40 @@ pub struct SurfaceConfiguration<V> {
     /// `AutoNoVsync` will gracefully do a designed sets of fallbacks if their primary modes are
     /// unsupported.
     pub present_mode: PresentMode,
-    /// Desired maximum number of frames that the presentation engine should queue in advance.
-    ///
-    /// This is a hint to the backend implementation and will always be clamped to the supported range.
-    /// As a consequence, either the maximum frame latency is set directly on the swap chain,
-    /// or waits on present are scheduled to avoid exceeding the maximum frame latency if supported,
-    /// or the swap chain size is set to (max-latency + 1).
-    ///
-    /// Defaults to 2 when created via `Surface::get_default_config`.
-    ///
-    /// Typical values range from 3 to 1, but higher values are possible:
-    /// * Choose 2 or higher for potentially smoother frame display, as it allows to be at least one frame
-    ///   to be queued up. This typically avoids starving the GPU's work queue.
-    ///   Higher values are useful for achieving a constant flow of frames to the display under varying load.
-    /// * Choose 1 for low latency from frame recording to frame display.
-    ///   ⚠️ If the backend does not support waiting on present, this will cause the CPU to wait for the GPU
-    ///   to finish all work related to the previous frame when calling `Surface::get_current_texture`,
-    ///   causing CPU-GPU serialization (i.e. when `Surface::get_current_texture` returns, the GPU might be idle).
-    ///   It is currently not possible to query this. See <https://github.com/gfx-rs/wgpu/issues/2869>.
-    /// * A value of 0 is generally not supported and always clamped to a higher value.
+    /// Desired maximum number of monitor refreshes between a [`Surface::get_current_texture`] call and the
+    /// texture being presented to the screen. This is sometimes called "Frames in Flight".
+    ///
+    /// Defaults to `2` when created via [`Surface::get_default_config`] as this is a reasonable default.
+    ///
+    /// This is ultimately a hint to the backend implementation and will always be clamped
+    /// to the supported range.
+    ///
+    /// Typical values are `1` to `3`, but higher values are valid, though likely to be clamped.
+    /// * Choose `1` to minimize latency above all else. This only gives a single monitor refresh for all of
+    ///   the CPU and GPU work to complete. ⚠️ As a result of these short swapchains, the CPU and GPU
+    ///   cannot run in parallel, prioritizing latency over throughput. For applications like GUIs doing
+    ///   a small amount of GPU work each frame that need low latency, this is a reasonable choice.
+    /// * Choose `2` for a balance between latency and throughput. The CPU and GPU both can each use
+    ///   a full monitor refresh to do their computations. This is a reasonable default for most applications.
+    /// * Choose `3` or higher to maximize throughput, sacrificing latency when the the CPU and GPU
+    ///   are using less than a full monitor refresh each. For applications that use CPU-side pipelining
+    ///   of frames this may be a reasonable choice. ⚠️ On 60hz displays the latency can be very noticeable.
+    ///
+    /// This maps to the backend in the following ways:
+    /// - Vulkan: Number of frames in the swapchain is `desired_maximum_frame_latency + 1`,
+    ///   clamped to the supported range.
+    /// - DX12: Calls [`IDXGISwapChain2::SetMaximumFrameLatency(desired_maximum_frame_latency)`][SMFL].
+    /// - Metal: Sets the `maximumDrawableCount` of the underlying `CAMetalLayer` to
+    ///   `desired_maximum_frame_latency + 1`, clamped to the supported range.
+    /// - OpenGL: Ignored
+    ///
+    /// It also has various subtle interactions with various present modes and apis.
+    /// - DX12 + Mailbox: Limits framerate to `desired_maximum_frame_latency * Monitor Hz` fps.
+    /// - Vulkan/Metal + Mailbox: If this is set to `2`, limits framerate to `2 * Monitor Hz` fps. `3` or higher is unlimited.
+    ///
+    /// [`Surface::get_current_texture`]: ../wgpu/struct.Surface.html#method.get_current_texture
+    /// [`Surface::get_default_config`]: ../wgpu/struct.Surface.html#method.get_default_config
+    /// [SMFL]: https://learn.microsoft.com/en-us/windows/win32/api/dxgi1_3/nf-dxgi1_3-idxgiswapchain2-setmaximumframelatency
     pub desired_maximum_frame_latency: u32,
     /// Specifies how the alpha channel of the textures should be handled during compositing.
     pub alpha_mode: CompositeAlphaMode,