How do I connect it to the microcontroller

[kszere]

I have two such printers. I'd like to use with Arduino. How do I connect it to the microcontroller. I hope that the project will be further developed! :)

[3zuli]

Sorry for the late reply. The connections are described in the code. You need to check the datasheet of your printer. If the printer is the shift register type, then it should have three pins: Clock, Data and Latch. Then the head probably has several Strobe pins for enabling the printing head. The connections are defined here:

//pins for serial communication with the module
const int dataPin=6;  
const int clkPin=7;
const int latchPin=8;

const int stbPins[6]={9,10,11,12,A0,A1};  //strobe pins

For this module you need a high-current 5V supply.
If you have the same module as me (CITIZEN LT-286), then this code should be ready for use. I kind of abandoned this project, as I don't have much time next to my school. However I still have the hardware lying around :)

[kszere]

Okay. I continue your project! :)

#1 Stepper Motor
UNO => L293D
D2 => 1A (PIN INPUT 1)
D3 => 4A (PIN INPUT 2)
D4 => 2A (PIN INPUT 3)
D5 => 3A (PIN INPUT 4)

L293D => STEPPER
1Y (OUTPUT 1) => A (PIN 1 black)
4Y (OUTPUT 2) => B (PIN 2 yellow)
2Y (OUTPUT 3) => An (PIN 3 brown)
3Y (OUTPUT 4) => Bn (PIN 4 orange)

L293D - power:
ENABLE 1 => 5V
VSS => 5V
VS=> 5V
ENABLE 2 => 5V
GND => GND

#2 Thermal Module
LT-286 => UNO
PIN_LT 4 => D6
PIN_LT 6 => D7
PIN_LT 5 => D8

POWER FOR THERMAL PRINTER
PIN_LT 13,14,15,16,17 P-GND => GND
PIN_LT 1,2,7,26,27,28 VH => +5V
PIN_LT 7 Vdd => +5V
PIN_LT 18 L-GND => GND

This connection is good? I buy l293d and thermal paper is beginning

[3zuli]

Sounds correct. Don't forget about the Strobe pins, you must connect them as well.
LT-286 => UNO
PIN_LT 8 => 9
PIN_LT 9 => 10
PIN_LT 10 => 11
PIN_LT 21 => 12
PIN_LT 22 => A0
PIN_LT 23 => A1
If the stepper is turning in wrong direction, just swap any two of its wires. Btw instead of the L293D, a much simpler solution would be to use the EasyDriver http://www.ebay.com/itm/EasyDriver-Shield-stepping-Stepper-Motor-Driver-V44-A3967-For-Arduino-/201414925354?hash=item2ee543dc2a
L293D requires you to generate the stepping sequence, whereas with EasyDriver you just feed it with pulses and it does the stepping (as well as microstepping and current limiting) automatically. This would require a slight change to the code, but it would simplify both the code and the wiring.
Good luck with the project!

[kszere]

Thanks you! I need only chip without module. I would like make new board drivers for this painter. You know other chip, who can using one data pin cable for control this stepper motor? :)

[3zuli]

Easydriver uses the A3967 IC. There are also other types of drivers, for example these are used often in 3D printers http://www.ebay.com/itm/For-Arduino-DRV8825-Stepper-Motor-Driver-Module-3D-Printer-RepRap-StepStick-CNC-/321875414856?hash=item4af1450f48 These use the DRV8825 chip.
I think these modules from ebay are even cheaper than buying the individual ICs from a supplier like DigiKey or Farnell. If I were you I'd probably use the entire module, it's cheaper and easier.

[kszere]

Okay. Thank you very much. I order this chip, test and select one better. I have two printers. Maybe I have more. :)